Skip to content

Audio Loudness (LUFS) Checker

Measure the integrated loudness of an audio file in LUFS and see how far it sits from -14 LUFS.

About Audio Loudness (LUFS) Checker

Audio Loudness (LUFS) Checker measures how loud a file actually sounds, rather than how tall its waveform looks. Choose one audio file — MP3, WAV, OGG or M4A, up to 50 MB and ten minutes — and it is decoded and filtered inside this tab, then reported as an integrated loudness figure in LUFS next to the distance from the streaming target of −14 LUFS.

The measurement follows the shape of the BS.1770 method. The signal is K-weighted first, with a high shelf at 1,682 Hz and a high-pass at 38 Hz, because the ear does not hear the extremes at the same level as the midrange. It is then cut into 400-millisecond blocks every 100 milliseconds, each block is turned into a loudness value, blocks quieter than −70 LUFS are dropped, and a second relative gate removes anything more than 10 LU below the average of what remains. The survivors are averaged back into a single number.

Also reported are the sample peak in dBFS, the duration, the channel count, and how many blocks survived the two gates. The sample peak is the highest individual sample, not a true-peak measurement, so it cannot see an over between two samples.

The comparison figure is the useful part: platforms turn loud uploads down and leave quiet ones alone, so a track sitting several units above −14 is losing dynamics for nothing. Everything is computed locally and nothing is stored, so a second reading means choosing the file again.

How to use Audio Loudness (LUFS) Checker

  1. 1 Choose one audio file — under 50 MB and under ten minutes.
  2. 2 Wait a few seconds while it is decoded and K-weighted in this tab.
  3. 3 Read the integrated LUFS figure and the gap to −14 LUFS; green means within one unit.
  4. 4 Check the sample peak and the block count to see how much of the file passed the gates.

Frequently asked questions

Is −14 LUFS a rule I have to hit?

It is a common streaming target rather than a law. Spotify and YouTube normalise loud material down to roughly that level, Apple Music uses a quieter reference, and broadcasters set their own. The figure is shown as a comparison point, not a pass or fail mark.

Is this a certified BS.1770 meter?

No, it is an approximation of the method. It skips the 48 kHz resampling step, uses the browser biquad filters instead of the reference coefficient tables, and reports sample peak rather than oversampled true peak. It is good enough to tell whether a mix is in the right region, not to sign off a broadcast delivery.

Why do some blocks get discarded?

Two gates remove silence and quiet passages. Blocks below −70 LUFS are dropped as silence, then a relative gate removes blocks more than 10 LU below the average of the rest, so a long fade-out does not drag the overall figure down.

Can I measure an album or several files at once?

No. One file is analysed per run, with a limit of ten minutes and 50 MB, because decoding a long lossless file needs several hundred megabytes of memory in the tab. Album gain cannot be calculated here.

Does the audio leave my device?

No. The file is read with the File API and decoded by the Web Audio API in the page, so it never goes over the network. Nothing is saved either — reloading the page clears the result.

Free, online, and private

Free to use

Audio Loudness (LUFS) Checker is completely free. There is no account to create, no login, and no hidden charge or usage limit.

Runs online in your browser

It is a free online tool that runs entirely in your browser. Nothing to download or install — open the page and start using it right away.

Your data stays private

All processing happens locally on your device. Your input is never uploaded, stored, or tracked, so it never leaves your browser.

How Audio Loudness (LUFS) Checker behaves in detail

These are the specifics of this implementation — the exact ranges, defaults and fixed settings you are working with.

Parameter Value
Input one audio file per run, chosen with the file picker; the accept filter is audio/* and there is no drag and drop
Guards files over 50 MB are refused before decoding, files over 600 seconds after decoding, and files shorter than 400 ms before any block can be measured
K-weighting a high shelf at 1,681.97 Hz with 4 dB of gain and Q 0.7071, followed by a high-pass at 38.13 Hz with Q 0.5, rendered by an OfflineAudioContext at the file's own sample rate
Blocks 400 ms blocks taken every 100 ms; each block reads minus 0.691 plus ten times the base-ten log of the summed channel mean square
Gating blocks below -70 LUFS are dropped first, then blocks more than 10 LU below the average of the survivors are dropped again
Reported fields integrated LUFS to one decimal, the gap to -14 LUFS, the sample peak in dBFS, the duration, the channel count and the surviving blocks out of the total
Comparison a gap within one LU reads on target; anything louder is flagged as will be turned down and anything quieter as quieter than target

Compiled from the implementation of this tool and checked against it by itoolnet.

What Audio Loudness (LUFS) Checker does not do

Knowing the edges of a tool saves more time than another list of its features. These are the cases where it will not do what you might expect.

  • It is an approximation of BS.1770, not a certified meter. There is no 48 kHz resampling, the filters are the browser biquad implementations rather than the reference coefficient tables, and the peak figure is the highest sample rather than an oversampled true peak, so it cannot see an over between two samples.
  • One file at a time, under ten minutes and 50 MB. There is no album mode, no batch queue and no loudness range, momentary or short-term readout - only the single integrated figure and how many blocks survived the gates.
  • Nothing is saved or exported. The result is not written to a file, not kept after a reload and cannot be compared against a second measurement on screen, and the reading is not a substitute for a delivery-specification check.

Tested and documented by itoolnet, the team that builds and maintains this site.

Share & embed this tool

Writing a guide or article? You are welcome to link to Audio Loudness (LUFS) Checker with the snippet below. It is free, runs entirely in your browser, and needs no signup.